Medien | smashd.de

Do not use this model without permission for comercial purposses.

Astronaut sitting on the moon

Complete or in 2 parts.

I glued the Astronout to the moon

20. Juli 2022

Blink Kamera Halterung Anycubic i3 Mega S Camera mount Amazon

Ich habe hier eine Halterung für die Amazon Blink mini WLAN Kamera entworfen. Die Halterung wird auf der linken Seite an den 2 oberen Schrauben befestigt. Die Kamera kann mit dem original Kugelkopf einfach eingeklipst werden.

19. Juli 2022

Dr strange zombie mask

Dr strange zombie full face mask. I printed upright with no problems except a slight nozzle block on couple of layers.I used tree support.

16. Juli 2022

Gloomhaven – HP/XP dial holder with Cutout

Added cutouts to the sides of peterstreasury3D’s Gloomhaven – HP/XP dial holder. They allow fingers to spin the dials more easily.

9. Juli 2022

USB to Dupont adapter for power supply 5V Arduino Raspberry Pi

This is a simple adaptor I created to not always solder cables and usb plugs. These are expensive too.. Two single male Dupont connectors can be inserted and when it is pluged into a USB port you are able to harness power from it for any reason imaginable. I use them to power my Lattepanda and after several prints and improvements I can proudly share this very handy gadget. I think it will be interesting for Arduino stuff.
Have fun 🙂

!!! Always make sure you connect it the correct way !!!
I am in no way responsible for any damage that occurs with this part.

21. Juni 2022

Steam Deck Dock/Base for Anker 341 USB-C Hub (7-in-1) A8346

Due to buildplate dimensions and not really needing the whole width (and height) of the original I have opted to cut off portions of the dock.
However I’ve left just enough of the slant/curves in so the Steam Deck more or less registers into the groove, kind of.

Just used Microsoft 3D Builder to substract/add stuff which took quite some time but as always I’ve included the 3mf file if you want to change something. It is at a later stage where the original dock was already cut to size, but you could just add the original in and just don’t cut off left/right/bottom.

Since I’ve won (yay!) the Anker 341 USB-C Hub (7-in-1, model A8346) I’ve added a slot on the back to slide that into. You have a cable channel for its main USB-C connection on the left and right and you may want to rotate it so you can have the USB-A ports top and the HDMI/USB-C PD port on the bottom … or vice versa. Do as you like or your cable management needs.

I am using a magnetic 40 Gbps USB-C 90 degree adapter by the way, which works great! Just keep in mind to not block the exhaust port on the top of your Steam Deck by routing the cable over the power button on the right, not over the vent on its left.

Here are the products I am using in case you may want to take a look or even buy them:

Items from Amazon DE

*Anker 341 USB-C Hub (7-in-1, model A8346):
https://www.amazon.de/?&linkCode=sl2&tag=smashdde-21&linkId=130bd56df0094b92f89443ed97311fd8&language=de_DE&ref_=as_li_ss_tl

*USB Type C Magnetic Adapter, USB4.0 40Gbps Data Transfer, 100W Quick Charge and 4K@60 Hz Video, but eg. Aliexpress could be a lot cheaper (got the connector in straight and angled for about 3.50 EUR each, the plugs itself can be bought seperately for even less):
https://www.amazon.de/?&linkCode=sl2&tag=smashdde-21&linkId=130bd56df0094b92f89443ed97311fd8&language=de_DE&ref_=as_li_ss_tl

*The used link(s) is/are so-called affiliate link(s). When you buy a product using this link, I will receive a small provision. The price itself does not change. Thanks so much for your support 🙂

Side note: since Steam Deck defaults to highest resolution available you might get 4k@30 at the moment in game mode. In desktop mode you can get it to output 1080p@120 (when your display/TV supports it) so I really hope Valve gives an option to force a specific resolution. Which should happen since they plan to release their own dock and probably run into the same issues there.

12. Juni 2022