head stl link : https://www.thingiverse.com/thing:4599252
I hope someone to cut models for 200mm bed and upload on remix
IRON MAN MK3 BUST(life size)
Drink / Bottle Coaster and Holder, Anti-Stick
During the current warm temperatures cold beverage can build up quite some amount of condensation on the table, especially when using glass bottles right from the fridge.
There always was quite some puddle below the (Sodastream in the picture) bottle which I was tired of so I designed these coasters.
The arrow/triangle pattern provides several purposes:
- hold the condensation
- wet surface does not stick to flat bottoms of drinks
- water in there can easily evaporate, no need to do anything
The lip around the coasters edge is a little bit higher so bottles/glasses don’t slide off.
The holder exists in two versions, one very basic and one more elaborate.
I have printed the coasters in transparent PETG which should make them quite resistant about getting wet all the time. And the higher temperature resistance isn’t to bad for direct sun light or putting them in hot water (to clean them) as well, I guess.
EBL Smart USB Charger Platform Battery Holder AA/AAA
I am using a simple USB charger to charge Eneloop AA batteries near my computer, so I wanted a simple holder of some sort to prevent them from rolling around.
This base clips in place and gives storage for two AA behind the charger.
Going from there I have mashed up several versions:
- 2 AA behind
- 4 AA on the right side
- 4 AA on the left side
- 4 AA on the left and right side: 8 AA in total
- 4 AA/AAA on the left and right side: 8 AA/AAA in total
Sure thing, Eneloops aren’t the cheapest, but I’ve got several years old ones in my rotation (don’t know exactly, but about 40 to 50 in AA/AAA?!) and ALL OF THEM are still perfectly fine!
As an alternative I can say Powerowl batteries have impressed me lately. For their very compelling price point they are delivering fantastically! They are low self-discharge as well. Measuring the AA and AAA variants over 5 cycles gave lower numbers than advertised but still higher than the Eneloop.
Amazon links* of equipment I am powering by AA/AAA:
EBL Smart USB Charger AA/AAA (<10€)
16x AAA Powerowl low self discharge 1000 mAh (measured at ~900)
16x AA Powerowl low self discharge 2800 mAh (measured at ~2200)
8x AA Eneloop
8x AAA Eneloop
Asus Republic of Gamers Strix Carry Mouse
Microsoft Xbox Wireless Controller Phantom Black
*The used links are so-called affiliate ones. When you buy a product using this link, I will receive a small provision. The price itself does not change. Thanks so much for your support 🙂
Cotton Swab Dispenser XXL
Modified the original to be quite a lot bigger, so it won’t waste space in my mirror wall cabinet.
Making it 4mm wider wasn’t quite nessecary, but oh well 🙂
about 120mm deep, about 120mm high
printed with transparent PETG by extrudr, which gives quite a good transparency with a wall thickness of 2 (default 0.4mm nozzle)
I did not make a fitting top/lid/cover, didn’t need one and knowing my printer … I just did not want to make 3 or 4 runs for a part to fit okay-ish that I don’t need. 😉
8bitdo SF30 Pro Dual Stand / Holder HIGH VERSION
I have made this quick and easily printable dual controller stand (high version) for my two 8bitdo SF30 Pros. You’ll probably need a little bit of glue to put the top and base parts together. With my printer/filament it was a tight snap fit but those are extremely random to get right. I would use glue anyway, wouldn’t want to risk this to fall apart with the controllers on 😉
3MF files are with separate meshes, if you like to change some proportions or something.
STL files are merged so you can drop them into your slicer.
8bitdo SF30 Pro Dual Stand / Holder
I have made this quick and easily printable dual controller stand for my two 8bitdo SF30 Pros. You’ll need a little bit of glue to put the top and base parts together. 😉
3MF files are with separate meshes, if you like to change some proportions or something.
STL files are merged so you can drop them into your slicer.
Folding phone holder
This is a total remodel from the original stand
Did not like the original model as it is quit wobble when lay flatten
so I designed a version that can be folded into itself
60° stand, can hold phone up to 14.5mm thickness (mainly for the Nintendo Switch )
Have 2 versions for clearance of 0.2 and 0.3mm
Print Size：60 x 165 x 10 mm
Can fold into 60 x 93 x 10 mm
Prints in a single piece, no assembly or screws required
Nintendo Switch Stand V2.0 (REMIX)
This stand works really well, but the swiveling support wouldn’t print right on my machine without supports and so I changed it to use a 45 degree angle so it wouldn’t be trying to print on nothing. I also changed the holes where the 2nd part of the stand go into so it would stay better.
8BitDo Grip (splitted)
I remixed „8Bitdo SF30 (SN30) Pro Grip 2.0 by DavidSL448“ to be able to print it without supports (except for the „arc“)
Also the rear „arc“ can be printed sideways and thus much stronger.
You’ll need to glue the 4 parts, I used gel super glue (Super Gel by Pattex)
GEMINUS Dual Filter Face Mask V2 for Coronavirus/COVID-19
Face mask to protect against air born viruses like coronavirus. Mask is not a one-size-fits-all. You may need to print at different scales to see which one works best.
Inspired by face mask from https://longliveyoursmile.com/3d-printable-mask-for-covid-19/
Features:
-Easy to clean design (no threads or complex parts)
-Comfortable fit (smoother, thicker contours and edges)
-Dual filters (use N95 particle sheets or round cotton pads)
-Moisture trapper (reduce moisture buildup at chin)
-Easy to breathe (Up to 300 cc of volume)
Instructions:
Scale to size for:
-Small – 95%
-Medium – 100%
-Large – 105%
1) Print with front of mask facing down on build plate with no supports.
Please see picture above.
2) Sand down any rough edges with 220 grit sandpaper.
3) Attach 1/4″ flat elastic bands to the mask.
See picture above for an example on how to attach.
4) Press fit filter sheets using an inner ring for each vent.
Optional:
1) Use a hair dryer to heat up edges and contour to your face.
2) Initial your masks in case you have more than one in the family.
Printing time: 3-6 hours depending on size
Disclaimer: This is not a replacement for proper N95 masks. If you can get your hands on N95 masks, please do so and use those. If you cannot, then having this is better than none.
Please comment on your fitment and any issues you had. Thank you.